Keyence Fs N10 Series User's Manual

F-2HA, Reflective Lens in FS-V/T/M series by KEYENCE India. Tcm:42-572964-64 To use all available functions on this website, JavaScript must be enabled in your browser. FS-N10, Fiber Amplifier, Zero-line Expansion Unit in FS-N series by KEYENCE America. Tcm:26-264674-64 To use all available functions on this website, JavaScript must be enabled in your browser. OP-73880, Mounting Bracket in FS-N series by KEYENCE INTERNATIONAL (BELGIUM). Tcm:56-936871-64 To use all available functions on this website, JavaScript must be enabled in your browser.

  1. Keyence Fs N10 Series User's Manual Software
  2. Keyence Fs N10 Series User's Manual S Manual Youtube

Fs-n10 series, Instruction manual, Digital fiber sensor

Advertising

1

Digital Fiber Sensor

FS-N10 Series

Instruction Manual

Read this manual before using the product in order to achieve maximum performance.

Keep this manual in a safe place after reading it so that it can be used at any time.

Hints on Correct Use

•

Do not wire the amplifier line along with power lines or high-tension lines, as the sensor may
malfunction or be damaged due to noise.

•

When using a commercially available switching regulator, ground the frame ground terminal
and ground terminal.

•

Do not use the FS Series outdoors, or in a place where extraneous light can enter the light-
receiving element directly.

•

Due to individual dispersion characteristics and the difference in fiber unit models, the maxi-
mum sensing distance or displayed value may not be the same on all units.

•

If the sensor is used for a long time with the APC function enabled and the LED is imposed
with a heavy load, the current consumption of the sensor for light emission will become con-
stant and 'END APC' will be displayed. The sensor can still be used in this case. However,
replace the sensor if even small changes in received light intensity should be detected for
precise detection.

Precautions on Regulations and Standards

„

UL Certificate

This product is an UL/C-UL Listed product.

•

UL File No. E301717

•

Category

NRKH,NRKH7

•

Enclosure Type 1 (Based on UL50)

Be sure to consider the following specifications when using this product as an UL/C-UL Listed Product.

•

Use the power supply with Class 2 output defined in NFPA70 (NEC: National Electrical Code).

•

Power supply/ Control input/ Control output shall be connected to a single Class 2 source only.

•

Use with the over current protection device which is rated 30V or more and not more than 1A.

Included accessories

•

Instruction Manual

1pc.

FS-N10 Series Quick Start

„

Quick Start

*1 This is a channel switch on 2-output types. This is not equipped with the 0-line type.
*2 Press and hold the [MODE] button to make advanced setting changes.

Names of Each Part of the Main Unit and Expansion Unit

*1 Setting to 'M' locks the power mode to MEGA mode. The switch is a channel switch for the

two output type. This is not equipped with the 0-line type.

*2 On the FS-N1

C

, this is an M8 connector rather than a cable. On the FS-N1

EN, this is

an e-CON connector.

Mounting Unit

„

Mounting on a DIN Rail

1

Align the claw at the bottom of the main body with
the DIN rail, as shown in figure1.
While pushing the main body in the direction of
the arrow 1, push down in the direction of arrow 2.

2

To dismount the sensor, raise the main body in
the direction of the arrow 3 while pushing the
main body in the direction of arrow 1.

„

Installation on a Wall (Main Unit Only)

1

Attach the unit to the optional mounting bracket (OP-
73880), and secure with two M3 screws as shown in
figure2.

Connecting Fiber Unit

1

Open the dust cover in the direction shown by
arrow 1.

2

Move the fiber lock lever in the direction shown
by arrow 2.

3

Insert a fiber unit into the amplifier as indicated
by arrow 3 (approximately 14 mm).

4

Move the fiber lock lever in the direction shown
by arrow 4 to secure the fiber.

Failure to follow these instructions may lead to death or seri-
ous injury.

Failure to follow these instructions may lead to injury.

Failure to follow these instructions may lead to product dam-
age (product malfunction, etc.)

Provides additional information on proper operation.

This provides useful tips for the feature being described.

See 'FS-N10 Series User's Manual' for details on the features of the FS-N10 Series and
detailed instructions for configuration.

•

This product is just intended to detect the object(s). Do not
use this product for the purpose to protect a human body or
a part of human body.

•

This product is not intended for use as explosion-proof
product. Do not use this product in a hazardous location
and/or potentially explosive atmosphere.

•

This product uses DC power. Do not apply AC power. The
product may explode or burn if an AC voltage is applied.

Danger

Warning

Caution

Note

Tip

Warning

Fine sensitivity adjustment

Mode/Output *2

Get help for your Acer! Identify your Acer product and we will provide you with downloads, support articles and other online support resources that will help you get the most out of your Acer product. Acer Aspire One D257 Service Manual Aspire One D257/Happy 2 SERVICEGUIDE, Acer AOD257 / Aspire One AOD257. (1x2GB) RAM Memory for Acer Aspire One D257-1682 (. How To Clear Bios Password Manuel Acer Aspire One D257-1497. (Posted by sunnylou 10 months ago) Popular Acer AOD257 Manual Pages. Aspire One AOD257. ASPIRE ONE D257 MANUALS. User manual for aspire one 257-1682. View and Download Acer Aspire One user manual online. Aspire One Laptop pdf manual download. Acer Aspire One User Manual. Also See for Aspire One. User manual - 764 pages Quick manual - 9 pages Specifications - 2 pages. Most useful pages: More. Recovering from recovery backup. Aspire ONE D257; Acer Aspire ONE D257 Manuals Manuals and User Guides for Acer Aspire ONE D257. We have 3 Acer Aspire ONE D257 manuals available for free PDF download: User Manual, Service Manual, Quick Manual.

Keyence Fs N10 Series User's Manual Software

Press the [MODE] button once, then

to select L-on or D-on

use

Preset function

Configure easily
with a single press
when receiving light

Down

Up

Power select switch *

1

Standard MEGA (fixed)

Setting value Light intensity

Sensitivity setting

Press once each for workpiece/no workpiece

Sub screen
(Displayed in green)

Main screen
(Displayed in red)

Dust cover

Fiber lock lever

Manual button

( )

MODE button (MODE)

Power select switch*

1

Cable*

2

Expansion
protective cover

Expansion connector

Preset button (PRESET)

SET button (SET)

Operation status indicators

Digital display

PST indicator

DTM indicator

3

2

figure1

1

OP-73880

figure2

Fiber insertion sign

1

3

2

4

96M11513

Advertising
Table of contents

Keyence Fs N10 Series User's Manual S Manual Youtube

  • Precautions on Regulations and Standards
  • FS-N10 Series Quick Start
  • Mounting Unit
  • Calibration Method
    • Detecting Even Small Differences
  • Other Calibration Methods
    • Increased Resistance to Dust and Dirt
    • Calibrate with a Moving Workpiece
    • Position Workpiece
  • Simple, User Friendly Functions
    • Setting the Current Value to 100.0
    • Set Current Value to '0'
    • Adjusting the current intensity value when it is too large (when saturated).
  • Connecting to External Devices
  • Initializing the Settings
    • Initialization Method
  • Using a Fiber Cutter and Cautions for Use
  • Function Configuration
Popular Brands
Popular manuals